Job description

INTERNSHIP, Electrical Engineering LOCATION: Onsite, Logan, UT Job Summary Support electrical engineering work at Juniper Systems while developing toward a full-time engineering or electrical design role. The intern works alongside experienced engineers on hardware that goes into rugged computers, GNSS receivers, accessories, and agricultural instruments. Depending on interest and aptitude, the intern can grow and contribute in the following areas: hands-on electrical design services, troubleshooting, prototyping, PCB layout, component libraries, design package release, hardware verification, circuit analysis, and component research. Job Duties and Responsibilities • Carries out test plans and verification work on prototype and pre-production hardware, records results accurately, and reports anomalies clearly. • Builds, reworks, and modifies prototype boards, cable assemblies, and test fixtures under the direction of engineers. • Helps investigate hardware problems found in development, manufacturing, and the field. Documents what was tested, what was found, and how to reproduce the failure. • Supports circuit analysis, component research, and specification review as assigned. • Supports electrical design tasks as assigned, such as schematic entry, PCB layout support, component library work, or preparing design release documentation. • Documents test methods, procedures, and findings in a form another engineer can follow. Skills, Knowledge, and Experience Enrolled in an electrical engineering, electrical and computer engineering, or electronics technology program at a university or technical college. Candidates earlier in their program are considered where aptitude is evident. Required: • Demonstrated hands-on experience building, testing, or troubleshooting electronic hardware through coursework, employment, or personal projects. • Ability to read schematics, datasheets, and technical drawings. • Careful, methodical attention to detail and a willingness to ask questions early rather than assume. • Clear written communication and careful record keeping. Preferred: • Experience with PCB design software, such as OrCAD, Altium, KiCad, or similar. • Hand soldering and rework on surface-mount components. • Familiarity with oscilloscopes, digital multimeters, bench power supplies, or similar lab equipment. • Coursework or project experience in circuit analysis, embedded systems, power electronics, or RF. • Effective use of AI-assisted tools, with the discipline to verify their output independently before relying on it. The above statements describe the general nature and level of work being performed in this job function. This is not intended to be an exhaustive list of all duties, and indeed additional responsibilities may be assigned by Juniper Systems. Juniper Systems, Inc. is an EQUAL OPPORTUNITY EMPLOYER All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, national origin, disability, veteran status, or any other status protected by law.

Requirements

Must-haves

INTERNSHIP, Electrical Engineering
LOCATION: Onsite, Logan, UT
Job Duties and Responsibilities
Carries out test plans and verification work on prototype and pre-production hardware, records results accurately, and reports anomalies clearly.
Builds, reworks, and modifies prototype boards, cable assemblies, and test fixtures under the direction of engineers.
Helps investigate hardware problems found in development, manufacturing, and the field. Documents what was tested, what was found, and how to reproduce the failure.
Supports circuit analysis, component research, and specification review as assigned.
Supports electrical design tasks as assigned, such as schematic entry, PCB layout support, component library work, or preparing design release documentation.
Documents test methods, procedures, and findings in a form another engineer can follow.
Skills, Knowledge, and Experience
Demonstrated hands-on experience building, testing, or troubleshooting electronic hardware through coursework, employment, or personal projects.
Ability to read schematics, datasheets, and technical drawings.
Careful, methodical attention to detail and a willingness to ask questions early rather than assume.
Clear written communication and careful record keeping.

Nice-to-haves

Experience with PCB design software, such as OrCAD, Altium, KiCad, or similar.
Hand soldering and rework on surface-mount components.
Familiarity with oscilloscopes, digital multimeters, bench power supplies, or similar lab equipment.
Coursework or project experience in circuit analysis, embedded systems, power electronics, or RF.
Effective use of AI-assisted tools, with the discipline to verify their output independently before relying on it.

Application prep

Use the role’s language and application details while tailoring your materials.

Keywords to mirror

Platform: paycor
Effort: medium